Videcon Concept Pro VHSD-810EXT Manual de usuario descargar pdf (Pagina 9)

1. Before power is applied, please check the cables carefully.

2. The camera ID of the controller must be identical to that of the target camera. The camera ID can be checked by

reading DIP switch of the camera.

3. If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.

4. If you changed camera protocol by changing DIP switch, the change will be eective after you reboot the camera.

5. Since the operation method can be dierent for each controller available, refer to the manual for your controller if

camera cannot be controlled properly.

Check Points before Operation

- If the camera is exposed the high temperature(over 50°)

for a long time, the camera can lose focus. As a result, you

will get a blurry image. In this case, enter ‘Preset key + 165’

to enable auto calibration.

If auto calibration is enabled, the camera will be re-focused

once every 6 hours. If you want to disable this function,

enter ‘Preset key + 165’.

Auto Calibration

- Max. 127 positions can be stored as preset positions.

The preset number can be assigned from 1 to 128, but 95

is reserved for starting OSD menu.

- Refer page 26 - ‘CONCEPT PRO SPEED DOME>FUNCTION

SETUP>PRESET SETUP’ for more detailed information.

Preset

- Check how to operate preset and pattern function with

keyboard controller/DVR in advance to operate camera

function fully when using keyboard controller/DVR.

- If keyboard controller/DVR has no pattern key or function,

use shortcut keys with preset numbers. For more

information, refer to ‘Reserved Preset’ below.

Preset and Pattern Function Pre-check

Some preset numbers are reserved to special functions.

Preset key + 95: Enters into OSD menu

Preset key + 131~134: Runs pattern function 1 ~ 4

Preset key + 141~148: Runs scan function 1 ~ 8

Preset key + 151~158: Runs group function 1 ~ 8

Preset key + 161: Sets relay output to OFF

Preset key + 161: Sets relay output to ON

Preset key + 165: Sets auto calibration to ON

Preset key + 166: Sets auto calibration to OFF

Preset key + 167: Zoom proportional jog ON

Preset key + 167: Zoom proportional jog OFF

Preset key + 170: Sets camera BLC mode to OFF

Preset key + 171: Sets camera BLC mode to HIGH

Preset key + 174: Sets camera focus mode to AUTO

Preset key + 175: Sets camera focus mode to MANUAL

Preset key + 176: Sets camera focus mode to SEMI-AUTO

Preset key + 177: Sets day & night mode to AUTO1

Preset key + 178: Sets day & night mode to NIGHT

Preset key + 179: Sets day & night mode to DAY

Preset key + 190: Sets OSD display mode to AUTO

(Except privacy mask)

Preset key + 191: Sets OSD display mode to OFF

(Except privacy mask)

Preset key + 192: Sets OSD display mode to ON

(Except privacy mask)

Preset key + 193: Sets all privacy mask display to OFF

Preset key + 194: Sets all privacy mask display to ON

Preset key + 195: Sets fan/heater to ON

(Turning o after 5 min, turn to auto mode)

Preset key + 196: Sets fan/heater to OFF

(After turning o, turn to manual mode)

Preset key + 197:

Fan ON(Turning o after 5 min, turn to auto mode)

Preset key + 198: Fan OFF(After turning o, turn to manual mode)

Preset key + 200: Sets digital zoom to ON

Preset key + 201: Sets digital zoom to OFF

Reserved Preset

Method 1) Use keyboard controller:

Refer to keyboard controller manual.

Method 2) Use OSD menu.

Method 1) Use keyboard controller:

Preset key + Number key(1~128)

2. Run Preset

To delete pattern, use OSD menu.

3. Delete Preset

1. Set Preset

- By using VST function, you can make the camera move

between 2 preset positions repeatedly.

- Refer page 28 - ‘CONCEPT PRO SPEED DOME>FUNCTION

SETUP>VST SETUP’ for more detailed information.

VST

Method 1) If there is VST key on the keyboard controller:

VST key + VST number(1~8) + Enter key

Ex) Run VST 2 = VST key + [2] + Enter key

Method 2) If there is no VST key on the keyboard controller:

Preset key + [VST number(1~8) + 140]

Ex) Run VST 2 = Preset key + [142]

2. Run VST

To delete VST, use OSD menu.

To set VST, use OSD menu.

3. Delete VST

1. Set VST

- Pattern function is that a camera memorizes the path

(mostly curve path) by joystick of controller for assigned

time and revives the path exactly as it memorized.

- Refer page 29 - ‘CONCEPT PRO SPEED DOME>FUNCTION

SETUP>PATTERN SETUP’ for more detailed information.

Pattern

To set pattern, use OSD menu.

1. Set Pattern

Method 1) If there is pattern key on the keyboard controller:

Pattern key + Pattern number(1~4) + Enter key

Ex) Run pattern 2 = Pattern key + [2] + Enter key

Method 2) If there is no pattern key on the keyboard controller:

Preset key + [Pattern number(1~4) + 130]

Ex) Run pattern 2 = Preset key + [132]

2. Run Pattern

To delete pattern, use OSD menu.

3. Delete Pattern

- The group function allows running sequence of presets,

pattern and/or VSTs.

- Refer page 30 - ‘CONCEPT PRO SPEED DOME>FUNCTION

SETUP>GROUP SETUP’ for more detailed information.

Group

To set group, use OSD menu.

1. Set Group

Method 1) If there is group key on the keyboard controller:

Group key + Group number(1~8) + Enter key

Ex) Run group 2 = Group button + [2] + Enter key

Method 2) If there is no group key on the keyboard controller:

Preset key + [Group number(1~8) + 150]

Ex) Run group 2 = Preset key + [152]

2. Run Group

To delete group, use OSD menu.

3. Delete Group

- The schedule function allows running an appropriate

function like preset, VST, group, pattern, home move at

the designated day and time.

- Refer Page 32 - ‘CONCEPT PRO SPEED DOME>FUNCTION

SETUP>SCHEDULE

SETUP’ for more detailed information.

Schedule

Check Points before Operation

16 17

Main Functions

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 21 22

Comentarios a estos manuales

Sin comentarios

Videcon Concept Pro VHSD-810EXT Manual de usuario Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Cámaras De Seguridad Videcon Concept Pro VHSD-810EXT